Specifications: Type: X Voltage: 220V, 50/60Hz Current: 2.8A Max. 0-210 Gross Weight: 6kg Package Dimensions: 291027cm Package Content: 1 x APF-260 Power Feed 1 x X-Axis Fix Stand with Bushing 1 x Bevel Gear with Fix Ring 1 x Handle Washer 2 x Stop Blocks 2 x Stop Set 2 x Socket Screws (M8P1.2535) 2 x Socket Screws (M8P1.025) 6 x Small Shims (126.96.36.199t) 2 x Small Shims (188.8.131.52t) 3 x Small Shims (184.108.40.206t) 4 x Large Shims (43.433.40.25t) 2 x Spring Pins 1 x Cable Clamp 1 x User Manual.
X-Axis Power Feed Table Milling Fit Bridgeport Milling Powerfeed Power Feeder 220v. Set the Fix Stand on Work Table, Set Table Bearing Bushing on the Axis Screw, Then Set the Power Table Feed on the Fix Stand, Take out the Gear Housing.
Use One Hand to Hold the Center Transmission Shaft. Set the Bevel Gear on Axis Screw with the Other Hand. Then Check If the Backlash Between Gears Is Between 0.1-0.2mm. Add Shims (1.0t, 0.25t, 0.1t) If the Backlash Is Too Large. Repeat Step 2-3 Until Reaching Satisfying Backlash.
Tighten the Handle to Start Setting Socket Parallel Key and Bevel Gear. Rotate the Handle Slightly to Feel If Any Interfere Occurs in Between. If Do, Please Repeat Step 3-4 to Add More Shims. If Not, Go to Next Step. Take out the Handle, Add Proper Shim (f43xf33), Adjust the Backlash Between Dial & Bevel Gear and Lock with Fix Ring.
Set the Handle and Tighten, Slightly Rotate the Handle. Normally It Should Be Smooth Without Any Interfere. Finally, Set the Gear Housing and Limit Switch. Function: Power Supply Switch and Reset Switch 1.
The Right Side of Power Switch Is "on". The Left Side Is off.
Red Light Will Show When Machine Is on. The Red Round Button on Right Side Is Reset Switch. Reset Button Will Jump up to Cut off the Power If the Machine Overloads.The Operator Must Reduce Cutting Load, Then Press Reset Switch to Continue Operating. Feed Knob and Rapid Button 1. Rotate Feed Knob After Power Is on. Turn Left for Left Side Feeding and Vice Versa. The Button in the Middle Is "Rapid Button".
Tool Will Travel Rapidly to Left Side If You Keep Pressing the Button. Release to Make Power Table Feed Will Back to Normal Speed.Speed Adjust Knob Speed Can Be Adjust According to Operator's Requirement, Ranging from 0-9. Jog Switch Normally, Jog Switch Should Be at "Feed" Position. For Jog Movement, Just Switch to "0" Position.
Kept Holding the Switch Until It Travels to Requires Position. Note: to Stop Jog Operating, You Must First Turn "Feed Knob" to "0"(off) Position.
Then Move "Jog Switch" to "Feed" Position. Be Sure to Follow the Procedure for Jog Operation to Avoid Any Damage Caused by Wrong Movement. Maintenance Gear Cover Must Be Open Every 6 Month to Check Whether Lubrication for Spiral Gear Is Sufficient.
Graphite Type Lubrication Is Suggested Rather than Silicon Type. Carbon Brush Cap Should Be Open Every 6 Month to Check If the Brush Has Wore out. Brush Should Be Replace Immediately If Its Length Is Under 5mm (Front and Back Brush Should Be Replaced Together).
Add an Auto Power Table Feed to Your Milling Machine! A Simple and Inexpensive Way to Increase Productivity! Small Volume and Easy Installation.Excellent Speed Control in the Entire Range. Jog Function Operates at Any Feed Speed. Power Table Feed Won't Vibrate or Strain in Low Speed. Direction Control Knob for Easy and Rapid Operation. Safety Feature to Protect Transmission Gear and Electronic Components.
1 X Apf-260 Power Feed. 1 X X-axis Fix Stand with Bushing. 1 X Bevel Gear with Fix Ring. 2 X Socket Screws (M8P1.2535).
2 X Socket Screws (M8P1.025). 6 X Small Shims (f26.2f16.20.25t).2 X Small Shims (f26.2f16.20.1t). 3 X Small Shims (f26.2f16.21.0t). 4 X Large Shims (f43.4f33.40.25t).
Feedback is very important to us. It is impossible to address issues if we do not know about them!Please keep the original box or packaging within 15days since item received. Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount.
Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday. The item "X-Axis Power Feed Kit Powerfeed Power Feeder For Milling Machine 135lb/in 210rpm" is in sale since Wednesday, October 27, 2021. This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment Replacement Parts".
The seller is "everytree58" and is located in Lausanne. This item can be shipped to United Kingdom.