US Free ship 4Axis Nema23 Stepper Motor 435oz. In 4.2A 3.4V Driver DM542A CNC Kit

4 pcs Stepper motor driver DM542A, PEAK 4.2A, 128 micsteps. 2 pc Power supply 350W-36vdc/9.7A. 1 pc parallel cable & 1 pc breakout board. Nema 23 stepper motor 435oz-in 23HS9442.

Stepper motor driver DM542A, PEAK 4.2A, 128 micsteps. Overvoltage, under voltage, overcorrect, phase short circuit protection. Pulse signal, PUL+ is the positive end of pulses input pin. PUL- is the negative end of pulse input pin. DIR signal: DIR+ is the positive end of direction input pin.

DIR- is the negative end of direction input pin. Enable signal: ENBL+ is the positive end of direction input pin.

This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver. ENBL- is the negative end of direction input pin. PCs control signals can be active in high and low electrical level.

When the high electrical level. Is active, all control negative signals will be connected together to GND. Level is active, all control positive signals will be connected together to public port. Two examples(Open collector &PNP), please check them.

Input port circuit (Yang connection). 2 Input port circuit (Yin connection). R must connect in the control signal part. Function choice (Using DIP pins to achieve this function).

1 Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table. SW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the. Selected dynamic current and ON meaning that standstill is set to be the same as the selected. The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current.

Closest to your motors required current. Semi-flow function is that there is not step pulse after 500 ms, the driver output current. Automatically reduced to 70% of rated output current, which is used to prevent motor heat. Pins of motor & power.

The power of this power supply is 350Watts, and the output voltage/current is 36VDC/9.7A. P2 P3 is set to X-axis for the X-axis pulse. P4 P5 is set to Y-axis, Y axis pulse. P6 P7 is set to Z-axis Z-axis pulse. The other can be set to A B C axis. A-axis pulse P8 P9 is set as the A axis. P14 is set to B-axis B-axis pulse P1. P16 P17 is set to C-axis, C axis pulse. Can also be set to the spindle control signal \ electrical permit. Input interface for the P10 P11 P12 P13 P15. It can connection 6 drivers and control 6 motors in the same time.

Description: Built in DB25 male connector. DB25 Output Pin:P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. DB25 Input Pin: P10, P11, P12, P13, P15. High quality with Surface-mount Tech.

The item "US Free ship 4Axis Nema23 Stepper Motor 435oz. In 4.2A 3.4V Driver DM542A CNC Kit" is in sale since Friday, August 17, 2018. This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "longsmotor-yy" and is located in Industry.

This item can be shipped worldwide.

Model: 23HS9442 DM542A 350W-36V B.B
Country/Region of Manufacture: China
MPN: Does not apply
Brand: LONGS MOTOR