UK? 4 Axis USB Mach3 CNC Kit Nema23 Stepper Motor CW5045 Driver Controller Set
4 Axis USB Mach3 CNC Kit Nema23 Stepper Motor CW5045 Driver Controller Set For CNC Router Milling Engraving Machine. A ustria, B elgium, B ulgaria, C zechRepublic, D enmark, E stonia, F inland, F rance, G ermany, G reece.
H ungary, I reland, I taly, L atvia, L iechtenstein, L ithuania, L uxembourg, M onaco, N etherlands, P oland. P ortugal, R omania, S lovakia, S lovenia, S pain, S weden, UK. 4 x CW5045 stepper motor driver. 4 x 23HS2430B Nema23 stepper motor. 1 x 400W 36V 11A switching power supply.
1x 4 Axis Mach3 USB Motion Card STB4100 V2.1. CD include user manual and mach3 software. Step Angle: 1.8 degree. Phase Resistance: 1.6ohms ; Inductance: 6.8mH+/-20%(1KHz). Frame Size: 57 x 57 x 112 mm.Front shaft 8mm dia and 21mm length, back shaft 8mm dia and 11mm length. Our motor is made of solid and durable metal. The perfect combination of rubber and rotor makes the internal structure more stable, and also reduces the vibration and noise when the engine runs.
The motor runs more quietly, with a high torque of 425oz in. The coil uses pure copper enamelled wire to ensure that long-term operation will not lead to excessive engine temperature. The rotor surface is coated with high-quality epoxy resin adhesive to isolate the adsorbed burrs on the rotor surface, more stable magnetic field and longer service life of motor. Stepper motor's red wire connect to driver's A+ port. Stepper motor's green wire connect to driver's A- port.Stepper motor's yellow wire connect to driver's B+ port. Stepper motor's blue wire connect to driver's B- port. Step angle accuracy:+ - 5%(full step, not load). Resistance accuracy: + - 10%. Inductance accuracy:+ - 20%.
Temperature rise: 80deg Max(rated current, 2 phase on). Ambient temperature -----------20deg ---- +50deg. Insulation resistance:100ohm Min, 500VDC. Insultion Strength--------500VAC for one minute. CW5045 high microstep stepper motor driver.
DC power input type:24V50VDC. Output current:1.3,1.8,2.3,2.7,3.2,3.7,4.2,4.5A. Mircostepping:1(1.8º), 1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256;1/5,1/10,1/25,1/50,1/125,1/250.
Protect form : Overheated protect, lock automatic half current, error connect protect. It is fit for NEMA17-23 two and four phase stepper motors whose current is small than 4.5A, it also can fit for small length NEMA34 two and four phase stepper motors. VCC+:DC power positive pole. A-:Stepping motor one winding. B-:Stepping motor other winding.PUL -:Stepping pulse input+5V. DIR-:Stepping motor direction input.
ENA- : no need to connect. Shape design is convenient for installation. Mircostepping: 1(1.8°), 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/5, 1/10, 1/25, 1/50, 1/125, 1/250.DC power input type: 24V50VDC. Output current: 1.3A-4.5A. Mach3 USB Motion Card STB4100 V2.1. 4 Axis USB Mach3 control board.
Power supply to isolate USB and external port, and to make the system more stable. MCU model: three generation 32-bit STM processor. Communication plug-in: RnR motion control card - ECO-2.0. 4 general-purpose isolated relay drive output interface, can drive four relays for. Controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.
4 general-purpose inputs, you can connect the. Limit switch, estop switch, probe, back to zero and other device.Support for 4 Axis linkage, you can connect. Four stepper motor drives or servo drives.
Which is suitable for the servo or stepping motor. You can use mach3 software to control the spindle motor speed.Indicate connection status on the board. Support for 4-axis linkage, you can connect four stepper motor drives or servo drives. Maximum step-pulse frequency is 100KHz, which is suitable for the servo or stepping motor. 4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stop.
Switch, auto tool zero, home switch etc. Support for connecting electronic handwheel. Have 0-10V signal output, you can use mach3 software to control the spindle motor speed.
4 general-purpose isolated relay drive output interface, can drive four relays for controlling. The spindle starts, forward rotating and reverse rotating, pumps or other device. 1 status LED, indicate connection status on the board. Dat" from "mach3 software folder, to C:\Mach3 Cover the. Original file, Reset Computermust reset the computr, please don't open the software dircetly!Way above the license for DIY or study purposes only, not for commercial use. Installation the software of the USB motion card. This USB motion card does not need install any USB driver, Windows2000/XP/Windows7/8/10, can. 1.3.1 Connecting the USB cable to the PC and the motion card.
The first installation of motion control card, take about 10s, when the green led lights on motion. Control card, indicating that the connection is successful, return the following tips when you.
The output current is steplessly adjustable to meet your various application requirements. It is also equipped with an automatic half-flow switch, which is easy to use. Use 6N137 high-speed optical lotus to ensure high speed without losing step.
The subdivision setting instructions are printed on the back of the board. Adopt enlarged radiator, good heat dissipation. With output short-circuit protection function, worry-free use. Adopting the common anode input mode, there are two input terminals, the wiring is more convenient. The working voltage is DC 10V-45V. It is recommended to use switching power supply DC32V for power supply. Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step. Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560. The rated maximum output reaches: ±4.5A. Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A.Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions. Please strictly follow the instructions and warnings before using this product. It is recommended that the. Limit switch and emergency stop switch must be installed first.
And can be used normally. The output singal of theelectronic handwheel must be. More than 5V output will damage the hand wheel interface. USB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with.
Does not require any drivers. To be installed, as long as. Can run, the control card can be used. Windows 2000/ XP / Windows 7/8/10. The inverter interface (AVI +, AVI-) is isolated from the computer and the main control circuit, and has.
No interference signal will be introduced due to the introduction of external strong electrical equipment. Whether frequency converter is supported: Yes. Number of control axes: X.
400W, Input:100-120VAC or 200-240VAC, 50/60Hz, Output:48v/8.3A, single output switching power supply. Embroidery machine, stage lighting, textile automation, printing. Problem&Feedback Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. Item must be in it's original condition and no physical damage.