NEMA34 4 Axis Stepper motor cnc kit 878oz-in 4A+Driver 24-80V 6A+5Axis boardDE

NEMA34 4 Axis Stepper motor cnc kit 878oz-in 4A+Driver 24-80V 6A+5Axis boardDE. For CNC Router Engraving Milling Machine. We have DE Warehouse located in. NO Duty & NO VAT to Below Europe countries. 4 x CW8060 stepper motor driver 6A 24-80VDC.

4 x 34HS9801 Nema34 stepper motor 878oz-in, 4A, 98mm. 4 x 400W 48V DC switching power supply. 1 x 5 Axis mach3 breakout board.

1 x DB25 parallel cable. 100% Brand New and High Quality!!

MACH3 145A 5 Axis Control board (V2.1). A special high speed chip is used to process the input and output (I/O) signals.

It is capable of making the machine work stably, with the features of correcting and enlarging the signals that removing the unnecessary disturb signals. The computer LPT port supplies the power individually, separating from the power supply of other parts. Therefore, the computer and machine tool isolate effectively. There are 5 input signals, communicating with the host computer, which are isolated by the optical coupling.

Among the optical coupling isolation, the P11and P12 are high-speed, which can be used for connecting main shaft encoder, or the same demanding signal as hand wheel A, B. 12V-OUT and 5V-OUT power output interface can be used to pick some necessary power, such as the hall sensor switch and the proximity switch.

There are 5 input ports, set to limit, origin, knife, start, stop, spindle speed input, MPG input and any other one of the 5 functions. There are 12 output signal, which is allowed to controlling output, supporting as many as 6 axis linkage. Some of the output port is reusable functinality. Meanwhile, one port only can be used as one function. There are 3 replays, P2, P3 and P4, which can support MACH3 control software programming.

The relay's on or off can be controlled through the control of MACH3 software. Each relay has attracted indicating lamp, which is more intuitive and convenient. The 3 relays can be used to control the opening and closing of the liquid coolant, mist coolant, liquid state coolant and so on. They can also be used to control the electromagnetic valve device power switch. P2 port is for the spindle, P3 port is for the cooling liquid, P4 port can be defined.

The high speed optical coupling isolation is used to control the rotational speed of spindle. The output port is parallel port P1, which can output the PWM signal within 2.5KHZ. On the interface board , there is a D/A circuit, with PWM to a 0-10V. The circuit can output 0-10V level to control the inverter which only has analog speed control in the market. Thus it can control the rotational speed of the spindle.

It is important that the PWM output and 0-10V output can only choose one in two. They can't be used at the same time. Interface board can be connected with the cathode or total output to the stepper drive, or servo drive (servo driver must support the digital signal).

The output is the 5Vlevel. Wide input voltage power supply: 15-32VDC. The function of preventing reverse connection protection. 2 groups of output voltage: 5V and 12V voltage, 100MA output capacity. Note: There is an enhanced version. Power supply voltage has a wider range: 15-50VDC. Do not insert the USB line to the computer's USB port. Just insert a LPT line. It is more convenient and reliable. The current output ability of 5V and 12V voltage output can upgrade to 200MA.

CW8060 256 microstep stepper motor driver 6A 24-80VDC. DC power input type: 24V80V. Mircostepping: 1(1.8deg), 1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256.

1/5,1/10,1/25,1/50,1/125,1/250. Protect form: Overheated protect, lock automatic half current, error connect protect. The maximum pulse rate is 100KHZ. It is fit for NEMA17-34 two and four phase stepper motors whose current is small than 6A. VCC+: DC power positive pole.

Must guard against exceeding 80V, so as not to damage the module. A+, A-: Stepping motor one winding. B+, B-: Stepping motor other winding.

CP+, CP-: Stepping pulse input+5V (Rising edge effective, rising edge duration >10uS). CW+, CW-: Stepping motor direction input, voltage level touched off, high towards, low reverse. The interface see; the right picture. Full current or half current choice.

SW4:0=Full current;1=half current. Usually default setting is single pulse. Nema34 878oz-in, L98mm Stepper Motor. High quality NEMA34 stepper motor. 400W, Input:100-120VAC or 200-240VAC, 50/60Hz, Output:48Vsingle output switching power supply. Please check out your address carefully when processing order.

We are not responsible for wrong or undeliverable address. 1530 workings days to most other countries. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos, we will help you to solve any problems. We work hard to make sure EVERY CUSTOMER 100% satisfaction. The item "NEMA34 4 Axis Stepper motor cnc kit 878oz-in 4A+Driver 24-80V 6A+5Axis boardDE" is in sale since Wednesday, September 29, 2021.

This item is in the category "Business & Industrie\Automation, Antriebe & Motoren\Elektromotoren\Schrittmotoren". The seller is "powace1515" and is located in Lausanne. This item can be shipped to European Union member countries, United Kingdom.

Current: 6A
Marke: RATTM MOTOR
Angebotspaket: Nein
Modifizierter Artikel: Nein
Herstellernummer: Does not apply
Driver: CW8060 6A,256 microstep
Stepper motor: Nema34 stepper motor
Step Angle(degrees): 1.8
Driver Microstep: 256 microstep
Size: 86x86x98mm
Shaft: single shaft
Model: 34HS9801/CW8060
Power supply: 400W 48VDC
Breakout board: 5 Axis breakout board
holding torque: 878 Oz-in /560Ncm
Phase: 2
Ausländisches Produkt: Nein
Driver input voltage: 24-80V DC