(GB) 3 Axis Nema 23 Stepper Motor 270oz.in 76mm+Driver+Control Board 36V CNC Kit
A ustria, B elgium, B ulgaria, C zechRepublic, D enmark, E stonia, F inland, F rance, G ermany, G reece, H ungary, I reland, I taly, L atvia, L iechtenstein, L ithuania, L uxembourg, M onaco, N etherlands, P oland, P ortugal, R omania, S lovakia, S lovenia, S pain, S weden. We will send this item from Germany Warehouse by DHL to EU Countries. Nema23 Stepper Motor 76mm, 270oz-in, 1.8kg/m, 3A. 3 x CW5045 Motor Driver (256 microstep, 4.5A). 1 x 350W 36V 9.7A DC Switching Power Supply.
1 x 5 axis breakout board V5 type. 1 x DB25 parallel cable. Step angle accuracy:+ - 5%(full step, not load). Resistance accuracy: + - 10%.
Inductance accuracy:+ - 20%. Temperature rise: 80deg Max(rated current, 2 phase on). Ambient temperature -----------20deg ---- +50deg. Insulation resistance:100ohm Min, 500VDC. Insultion Strength--------500VAC for one minute. Step Angle: 1.8 deg. Holding Torque: 1.8Nm (270oz. Frame Size: 57 x 57 x 76 mm. DC power input type:24V50VDC. Output current:1.3A-4.5A. Mircostepping:1(1.8ยบ) 1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256. 1/5,1/10,1/25,1/50,1/125,1/250. Protect form : Overheated protect, lock automatic half current, error connect protect. It is fit for NEMA17-23 two and four phase stepper motors whose current is small than 4.5A, it also can fit for small length NEMA34 two and four phase stepper motors. Full current or half current choice : SW4:0=Full current; 1=half current. To avoid use in the oil contamination, dust and corrosive gas environment. To lay it in a place with good ventilation. Pls note the connection with right power(+ and -) to avoid broken the driver. Pls test it when confirm the connection is right. 5 Axis LPT Port breakout board. 5 axis breakout board with DB25 parallel cable and USB cable. It can most connection 5pcs driver and control 5pcs motor in the same time. It is with relay port to control the cnc spindle. Working voltage is 5VDC and support with MACH3, EMC2, KCAM4 software. Breakout board EN connect driver's EN- port. Breakout board DIR connect driver's DIR- port.Breakout board STEP connect driver's PUL- port. 5V connect driver's EN+, DIR+ and PUL+. It is with 4-wire limit switch port. It is with 4-wire limit switch to insure our safty movement.
It is with relay port to contro the cnc spindle. 25-pin parallel port control is defined as follows. The pin of the drive board. B(Fifth axis)pulse signal. X(First axis) pulse signal. X(First axis) direction of the signal. Y(Second axis)direction of the signal. Z(Third axis) pulse signal. Z(Third axis) direction of the signal. A(Fourth axis) pulse signal. A(Fourth axis) direction of the signal. B(Fifth axis) direction of the signal.350W 36V 9.7A DC Switching power supply. It comes with built-in cooling fan. +V: DC power output "+". V: DC power output "-".
+V ADJ: output voltage regulation. Item must be in it's original condition and no physical damage. We are happy to have your questions. We are here to solve them by the friendly and quick ways.
This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "kuku218" and is located in this country: DE. This item can be shipped to United Kingdom, European Union.
- Breakout board: 5 axis V5 breakout board
- Size: 57x57x76mm
- Driver name: CW5045
- Power supply: 350W 36V 9.7A DC Switching Power Supply
- Supoort Software: MACH3,EMC2,KCAM4 etc
- Name: 3 Axis CNC Stepper Motor Controller Kit
- Step Angle(degrees): 1.8 degrees
- Brand: RATTM MOTOR
- Stepper motor: Nema23 stepper motor
- Application 1: Semiconductor Equipmen
- Shaft: Dual shaft
- Model: 23HS8430/CW5045
- Driver Microstep: 256 microstep
- holding torque: 270oz-in
- Country/Region of Manufacture: China