EU 4 Axis USB Mach3 Control CNC Kit Nema23 Stepper Motor Driver 270oz-in 76mm

EU4 Axis USB Mach3 Control CNC Kit Nema23 Stepper Motor Driver 270oz-in 76mm For CNC Router Milling Engraving Machine. Free duty to below EU Customers.

A ustria, B elgium, B ulgaria, C zechRepublic, D enmark, E stonia, F inland, F rance, G ermany, G reece, H ungary, I reland, I taly, L atvia, L iechtenstein, L ithuania, L uxembourg, M onaco, N etherlands, P oland, P ortugal, R omania, S lovakia, S lovenia, S pain, S weden. We will send this item from UK/Germany Warehouse by DHL/DPD to EU Countries. 4× Tb6600 stepper motor driver. 1× 4 Axis Mach3 USB CNC control board. 1× 350W 24V DC Switching power supply.

100% Brand New and High Quality!! Nema23 Stepper motor 76mm/270Oz-in/ 3A 1.8Nm. Step angle accuracy: ±5%(full step, not load). Temperature rise: 80deg Max(rated current, 2 phase on). Insulation resistance:100M Min, 500VDC. Insultion Strength--------500VAC for one minute. TB6600 stepper motor driver 4.5A. The working voltage is DC 10V-45V. It is recommended to use switching power supply DC32V for power supply. Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step. Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560. The rated maximum output reaches: ±4.5A. Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A. Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions. The working voltage is DC 10-45V; it is recommended to use DV32V switching power supply. There are two input terminals, both of which adopt the common anode input mode. The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required. The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked. The motor rotates forward when CW is high or suspended, and reverses when it is low.

When EN is high or floating, it is working state, when it is low, it is offline. The power supply cannot be connected reversely, otherwise the chip will be burnt out. The set current should not exceed the rated current of the motor.

Mach3 USB motion control board 4 axis. The motion control card for machine control, with strong professional. Requires the operator to have the relevant expertise! Please strictly follow the instructions and warnings before using this product. If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power.

It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally. This USB motion card does not need install any USB driver, Windows2000/XP/Windows7, can directly identify. 4-axis linkage, Maximum step-pulse frequency: 100KHz, support connect four stepper motor drives or servo drives. Signal Output:0-10V, it can control the spindle motor speed through using mach3 software.

4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stop. 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps or other device. Support for connecting electronic handwheel.

Note: the output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface. 350W 24V DC switching power supply. DC output: 24V 0-14.5A.

DC voltage of Adjustable range: ±10%. AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switch. Overload protection: 105%-135% cut off the output, automatic recovery. Over-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recover. Setup/rise/hold-up time: 200ms50ms20ms/230VAC at full load. Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute.

Isolation resistance: I/P-O/P I/P-FGO/P-FG: 500VDC/100M. Item must be in it's original condition and no physical damage. We are happy to have your questions. We are here to solve them by the friendly and quick ways.

The item "EU 4 Axis USB Mach3 Control CNC Kit Nema23 Stepper Motor Driver 270oz-in 76mm" is in sale since Thursday, November 5, 2020. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "kuku218" and is located in Frankfurt. This item can be shipped to European Union member countries.

Country/Region of Manufacture: China
Step Angle(degrees): 1.8 degree
Application 2: Milling Machine, Engraver machine
Application 1: Semiconductor Equipmen
Shaft: Dual Shaft
Motor Size: 57x57x76mm
Name: 4 Axis Nema23 Stepper motor usb CNC Controller Kit
MPN: Does Not Apply
Phase: 2 Phase
Driver: TB6600 Driver
Breakout Board: USB Mach3 Motion Control Board
Type: Hybrid
Lead wire: 4pcs
Model: 23HS2430B/TB6600
Driver Microstep: 16 microstep
Power supply: 350W 24V/10A
Current: 3A
Holding Torque: 180N.
cm/18kg-cm 270 oz-in
Brand: RATTM MOTOR