ES4 Axis Nema23 112mm Stepper Motor 425oz-in Dual shaft + Driver Mach3 CNC Kit

ES4 Axis Nema23 112mm Stepper Motor 425oz-in Dual shaft + Driver Mach3 CNC Kit. EU Customers don't need pay VAT or Tariff. A ustria, B elgium, B ulgaria, C zechRepublic, D enmark, E stonia, F inland, F rance, G ermany, G reece. H ungary, I reland, I taly, L atvia, L iechtenstein, L ithuania, L uxembourg, M onaco, N etherlands, P oland. P ortugal, R omania, S lovakia, S lovenia, S pain, S weden. (425oz-in, 112mm, 3A, 1.8deg). 4 x CW5045 motor driver. (24-50V DC, 4.5A, 256microstep).

1 x 400W 36V 11A switching power supply. 1 x 5 Axis breakout board V5 type.

1 x DB25 parallel cable. 4 Axis for medium size Router Mill Plasma or Laser.

It can most connection 5pcs driver and control 5pcs motor in the same time. It is with 4-wire limit switch to insure our safty movement. It is with relay port to contro the cnc spindle.

Working voltage is 5VDC and support with MACH3, EMC2, KCAM4 software. 25-pin parallel port control is defined as follows. The pin of the drive board.

B(Fifth axis)pulse signal. X(First axis) pulse signal. X(First axis) direction of the signal. Y(Second axis)direction of the signal. Z(Third axis) pulse signal.

Z(Third axis) direction of the signal. A(Fourth axis) pulse signal.

A(Fourth axis) direction of the signal. B(Fifth axis) direction of the signal. CW5045 high microstep stepper motor driver. Output current: 1.3,1.8,2.3,2.7,3.2,3.7,4.2,4.5A. Mircostepping: 1(1.8°), 1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256.

1/5,1/10,1/25,1/50,1/125,1/250. Protect form: Overheated protect, lock automatic half current , error connect protect. It is fit for NEMA17-23 two and four phase stepper motors whose current is small than 4.5A. Full current or half current choice : SW4:0=Full current; 1=half current. To avoid use in the oil contamination, dust and corrosive gas environment.

To lay it in a place with good ventilation. Pls note the connection with right power(+ and -) to avoid broken the driver. Pls test it when confirm the connection is right.

Step angle accuracy:+ - 5%(full step, not load). Resistance accuracy: + - 10%.

Inductance accuracy:+ - 20%. Temperature rise: 80deg Max(rated current, 2 phase on). Ambient temperature ----------20deg ---- +50deg.

Insulation resistance:100ohm Min, 500VDC. Insultion Strength--------500VAC for one minute.

400W, Input:100-120VAC or 200-240VAC, 50/60Hz, Output:36v/9.7 A, single output switching power supply. It is impossible to address issues if we do not know about them! The item "ES4 Axis Nema23 112mm Stepper Motor 425oz-in Dual shaft + Driver Mach3 CNC Kit" is in sale since Tuesday, November 6, 2018. This item is in the category "Equipamiento y maquinaria\Automatiza., motores y ejes\Motores eléctricos\Motores de uso general". The seller is "powace1515" and is located in Prague. This item can be shipped to European Union member countries.

• Marca: RATTM MOTOR
• Anuncio de conjunto: No
• MPN: No aplicable
• Producto no nacional: No
• Artículo modificado: No
• Name: 4 Axis Stepper Motor Mach3 Controller Kit
• breakout board: 5 axis V5 breakout board,fit for MACH3/EMC2/KCAM
• Model: 23HS2430B/CW5045
• Size: 57x57x112mm
• Driver Microstep: 256 microstep
• Shaft: Dual shaft
• holding torque: 425oz-in

---