4 Axis Nema34 Stepper Motor 116mm/1230oz-in& CW8060 Driver 6.0A 24-80VDC CNC Kit

4 Axis Nema34 Stepper Motor 116mm/1230oz-in/5A& CW8060 Driver 6.0A 80VDC CNC Kit for CNC Router Milling Engraving Machine. 4 x 34HS4802B Nema34 stepper motor Dual Shaft. 4 x CW8060 stepper motor driver 6A.

4 x 400W 60V DC switching power supply. 1 x 5 Axis breakout board V5 type.

1 x DB25 parallel cable. It can most connection 5pcs driver and control 5pcs motor in the same time. It is with 4-wire limit switch to insure our safty movement. It is with relay port to contro the cnc spindle.

Working voltage is 5VDC and support with MACH3, EMC2, KCAM4 software. CW8060 high microstep stepper motor driver. DC power input type:24V80V. Mircostepping:1(1.8deg), 1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256.

1/5,1/10,1/25,1/50,1/125,1/250. Protect form: Overheated protect, lock automatic half current , error connect protect. The maximum pulse rate is 100KHZ. VCC+:DC power positive pole. Must guard against exceeding 80V. So as not to damage the module. A+, A-:Stepping motor one winding. B+, B-:Stepping motor other winding. CP +, CP -:Stepping pulse input+5V (Rising edge effective, rising edge duration >10uS).

CW +, CW-:Stepping motor direction input, voltage level touched off, high towards, low reverse. 1, When ambient temperature is high or working current over 3A, fix the module on big metal shell , or use axle flows fan dispels the heat, to make the module run reliably for a long time. 2, Half current automatically: if control machine not send out signal in half second, driver enter half current state of automatically for electricity saving, the phase current of the winding of the electric. 3, The fault phase is protected : When the double-phase electrical machinery is connected with driver , users are apt to connect the phase by mistake, thus would damage the driver seriously. The protecting circuit is within this driver, when users connect by mistake, the driver will not be damaged, but the electrical machinery runs abnormally, shake , and output is small.

Please check whether the wiring of electrical machinery is a mistake. Full current or half current choice. SW4:0=Full current;1=half current. Usually default setting is single pulse. High quality NEMA34 stepper motor. Note:We can manufacture products according to customer's requirements. 400W, Input:100-120VAC or 200-240VAC, 50/60Hz, Output:70v/5.8A, single output switching power supply.

Please check out your address carefully when processing order. We are not responsible for wrong or undeliverable address. 1530 workings days to most other countries. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos, we will help you to solve any problems.

We work hard to make sure EVERY CUSTOMER 100% satisfaction. The item "4 Axis Nema34 Stepper Motor 116mm/1230oz-in& CW8060 Driver 6.0A 24-80VDC CNC Kit" is in sale since Tuesday, July 21, 2020. This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Electric Motors\General Purpose Motors". The seller is "powace1515" and is located in Changzhou,Jiangsu. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Mexico, Australia.

Model: 4 Axis CNC stepper motor controller kit
Driver: CW8060 6A,256 microstep
Power supply: 400W 60VDC
Phase: 2
Holding Torque: 1230oz-in /850Ncm
Name: 34HS4802B/CW8060
breakout board: 5 axis MACH3 breakout board
Step Angle(degrees): 1.8 deg
MPN: Does not apply
Brand: RATTM MOTOR
Country/Region of Manufacture: China
Motor size: 86X86X116mm
Driver Voltage: 24-80V DC
Driver Current: 6A
Type: Hybrid