Cnc Axis Kit

4 Axis CNC Stepper Motor TB6560 Board Controller Driver NEMA23 Kit Mach3 360W

4 Axis CNC Stepper Motor TB6560 Board Controller Driver NEMA23 Kit Mach3 360W

4 Axis CNC Stepper Motor TB6560 Board Controller Driver NEMA23 Kit Mach3 360W
TB6560AHQ 4 Axis CNC Stepper Motor. NEMA23 Kit Mach3 360W 24V 15A Power Supply. Chip - High power, maximum 3.5A drive current chipset. 1-1/16 microstep setting - Higher accuracy and smoother operation than standard 1, 1/2 step. Full closed-type optical isolation to protect the user's computer and equipment. Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment. On board current switching - Power output can be set according to specific user requirement. Adjustable 1.5A-3A drive current settings for each axis - 25%, 50%, 75%, 100% of full current can be set for different stepper motors. Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output). 4 channel inputs interface- Can be used for XYZ limit and emergency stop. Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop.

Professional design - Two stage signal processing with super anti- jamming. Bipolar constant current chopper drive with non-resonant region - Controls motors smoothly through range without creep effect. Universal architecture - Supports most parallel software MACH3, KCAM4 etc.

12-16V DC power supply for Nema 17 stepper motors 16-24V DC power supply for Nema 23 stepper motors 24-36V DC power supply for Nema 34 stepper motors. High voltage will burn up the chips or stepper motors!!!

Output current of the power supply can be calculated by the following expressions. Output current = Rated current of your stepper motors quantity + 2A. For example, if you want to drive 3 3A Nema 23 stepper motors, theoretically 24V 11A DC power supply is recommended, but higher power such as 24V 15A also will be good.

The power output of 12V shall be applied to the radiator fan of 12V. Driver output compatible with 2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max. Suitable for unipolar or bipolar stepper motors. Voltage regulated spindle speed controlled by parallel interface as function of supply voltage. Shaft Radial Play: 0.06Max.

Shaft Axial Play: 0.08Max. Step Angle Accuracy: ±5%(full step, no load). (ratod current, 2 phase on). Dielectric Strength: 500V AC for one minute. Remote is defined as islands and highlands; or a post code/zip code that is difficult to serve; or a suburb/town that is distant, inaccessible or infrequently served.

We are looking forward to a further extension of pleasant business relation. 1 x 4 Axis TB6560 Driver Controller Board.

4 x 57mm 57BYGH56 1.2N Stepper Motors. 1 x 350W 24V Power.

ECheque will be held until cleared. This item is ALL BRAND NEW and in the original factory box and packing, All products have been checked and packaged in good condition before dispatch. We will give you a return ID.

Meanwhile Please tell us what the defect is, to eliminate improper use. The item "4 Axis CNC Stepper Motor TB6560 Board Controller Driver NEMA23 Kit Mach3 360W" is in sale since Thursday, May 24, 2018. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Other Automation Equipment".

The seller is "gold-bucket" and is located in Shenzhen. This item can be shipped worldwide.

  • Brand: HY
  • MPN: XYCL0280
  • Country/Region of Manufacture: China
  • Model: HY-TB6560-4


4 Axis CNC Stepper Motor TB6560 Board Controller Driver NEMA23 Kit Mach3 360W