4 Axis CNC Router Kit Nema 23 Stepper Motor 270Oz-in &4P MD430 Driver &Power? EU

4 Axis CNC Router Kit Nema 23 Stepper Motor 270Oz-in &4P MD430 Driver &Power Supply for CNC Router Engraving Milling Machine. Welcome European customers to our shop. So it's free import duty to you!! 2-4 days to: Austria, France, Spain and Italy. 4-5 days to: Other Europe Countries. 4 x 23HS8430B Dual Shaft Nema23 Stepper Motor (3A, 76mm, 1.8deg, 180N. 1 x 350W 24V 10A DC switching power supply. 1 x 5 Axis breakout board. 1 x DB25 parallel cable. 100% Brand New and High Quality!!

TB6560 MD430 Low noise of stepper motor driver. MD430 is a compact single axis bipolar3.0A/phase stepper motor microstepping driver with step and directioninputs, DIP switch settable step mode (full, half, eight andsixteenth--S3/S4), torque (100%, 75%, 50%, 20%--S5/S6), work current(0-3A--SW1/SW2/SW3) and decay mode (0%, 25%, 50% and 100%). 1 Single-chip motor driver for sinusoidal microstep control of stepping motors. 2 Power on in indication led.

3 3Amps-34Volts(Supply voltages:12-34DC). 4 Full step, half step, eight step and sixteenth step(selection with dipswitches). 5 Torque (100%, 75%, 50%, 20%).

6 Work Current (0-3A selection with SW1/SW2/SW3). 7 4 Wire, 6 Wire, 8 Wire stepper motors can be used. 8 Two phases bipolar driver. 9 Easy wiring with standard screw terminals.

10 Step frequency up to 100khz. 11 Fuse protection on power supply rail(protects the board, but also your power supply and motor). Suitable for all kinds of small andmedium-sized automation equipment and apparatus For example, lasermachines, laser engraving &cutting machine, laser subsurfaceengraving machine, laser handicraft cutting machine, (nonmetalmaterials) laser marking machine, laser seals engraving machine andphotosensitive seal machine. 5 axis CNC Breakout board interface adapter board. 1, full support for MACH3, KCAM4, EMC2, the PC software to support parallel port control.

2, leads to all the parallel port of all 12 data transmission output pin, which can control the five stepper motor driver. 3, with 5-way input interface, you canaccess the limit switches and emergency stop switch, reset knife;5 input LED indicates the status of the input.

4, all the way with a 12A relay control, normally open, normally closed leads, user-friendly connection. 5, power supply with 5V USB power supply or external power supply to facilitate the access of external powersupply;On the external drive enable signal amplification, filtering, enhancement processing. 6, the pulse, the direction of signal shaping, enhanced with a carrying capacity, data transmission speeds reach 10 MBit / S. 7, the output pin with extension interfaces can 2.54mm pin 2.54mmXH-Block. 1, the use of new imported Japanese Toshiba TB6560 chip (disguising).

2, The base used dense teeth radiator, cooling super, to ensure the stable operation of equipment. 3, the input signal using a high-speedopto-isolation to ensure not losing steps, which the pulse directionsignals with the same level of 6N137, dual high-speed optocoupler. 4 a variety of semi-flow mode and the semi-flow current selection, the use of more flexible.

5, Decay mode is adjustable to ensure the motor running smooth. 6., Sophisticated appearance size cooling pad size: 75mm 65mm, four mechanical installation positioning holesize is: 67mm 58, mounting hole diameter is 4mm.

7, Set method detailed table on the board, easy to use. 8, With anti-reverse circuit, even if not careful the power plug back and will not burn the chip, the use of safer. Step angle accuracy:+ - 5%(full step, not load). Resistance accuracy: + - 10%. Inductance accuracy:+ - 20%.

Temperature rise: 80deg Max(rated current, 2 phase on). Ambient temperature -----------20deg ---- +50deg. Insulation resistance:100ohm Min, 500VDC. Insultion Strength--------500VAC for one minute. RED: A+ GREEN: A- YELLOW: B+ BLUE: B. 350W, Input:100-120VAC or 200-240VAC, 50/60Hz, Output:24v/10 A, single output switching power supply.

Please check out your address carefully when processing order. We are not responsible for wrong or undeliverable address.

Please give us the opportunityto resolve any problem when you have, we concern your problem and we will try our best to resolve it. We work hard to make sure EVERY CUSTOMER 100% satisfaction. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos to us. Item must be in it's original condition and no physical damage. We are online from Monday to Saturday.

This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Other Automation Equipment". The seller is "powace1515" and is located in this country: DE. This item can be shipped to United Kingdom, European Union.

Stepper motor Size: 57x57x76mm
Phase: 2 phase
Holding torque: 270oz-in 180Ncm 1.8N.
m
Breakout board: 5 Axis CNC breakout board Mach V5
Custom Bundle: No
Driver: TB6560 MD430 driver board
Driver Voltage: 12~34V
Power supply: 350W 24V/10A
Modified Item: No
Step Angle(degrees): 1.8
Brand: RATTM MOTOR
Shaft diameter: 8mm diameter shaft
Model: 4 axis CNC stepper motor controller kit
Shaft: Dual shaft
Driver Microstep: 128 microstep
Motor/Driver Model: 23HS8430B/MD430
Country/Region of Manufacture: China
Current: 3A