4 Axis 1.2N Stepper Motor 3.5A Driver TB6560 Nema23 USB Interface Board CNC Kit

4 Axis 1.2N Stepper Motor 3.5A Driver TB6560 Nema23 USB Interface Board CNC Kit. M Stepper Motor 3.5A Driver TB6560 Nema23 USB Interface Board CNC Kit.

CNC USB Interface Breakout Board. 1: The maximum matching 5-axis stepper motor driver 2: The two-stage signal processing, signal transmission smooth, powerful anti-jamming 3:5 input interface to define the emergency stop, limit, points in the knife, etc. 4: relay output control interface, can be accessed by the spindle motor or the air pump, water pump, etc 5: five-axis job LED display, visual display products, working condition. Input Power:5V DC power supply or computer USB to take power.

Work axis stepper:Received the highest 5-axis independent driving. Drive:Pulse + direction + enable signal. HY-DIV168N-3.5A subdivision-type two-phase hybrid stepping motor drive using DC 12 36V power supply, suitable for drive Two-phase hybrid stepping motor dynamic voltage 12 to 36V, the current is less than 3.5A outer diameter of 35 to 86 mm. This drive using the drive's current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth, almost no vibration and noise. High-speed torque is much higher than other two-phase drive, high positioning accuracy.

Widely used in the engraving machine, CNC machine tools, packaging machinery and other high resolution requirements on the device. Average current control, two-phase sinusoidal current drive output. DC 12 36V power supply, the internal integration of 12V and 5V regulator. Optically isolated signal input / output. Overvoltage, undervoltage, overcurrent, and white short-circuit protection.

4 file segmentation and automatic half-streaming capabilities up to 16 segments. File output phase current settings. Input voltage DC 12 36V input.

The input current of 1 to 4 amps, select the drive a stepper motor. Output current of 0.5A 3.5A.

Temperature Operating Temperature -10 to 45? Humidity not condensing, not drops. Gas prohibit combustible gas and conductive dust. The definition of control signals : PUL +: step pulse signal is input side or the positive pulse signal input positive terminal PUL-: the negative input of the negative input pulse signal or a positive pulse signal DIR +: stepping direction signal input to the positive terminal or negative pulse signal input to the positive terminal DIR -: stepping direction signal input of the negative side or reverse step pulse signal input negative terminal EN +: offline can reset signal input side is EN-: offline can reset signal input negative terminal Offline enable signal is active, reset drive failure to prohibit any pulse, the output of the drive Power component is turned off, the motor holding torque. Control signal connections : PC control signal can be high, also can be low effective.

When active high, the control signal The negative side together as a signal to active low, positive side of all control signals together as a signal common. 4.57BYGH56-401A Stepper Motor1.2N.

Step Angle Accuracy: +-5%(full step, no load). Resistance Accuracy: +-10%- Inductance Accuracy: +-20%. Temperature Rise: 80 Degrees Celsius CMax. (ratod current, 2 phase on)- Ambient Temperature: -10°C-+50°C.

Dielectric Strength: 500V AC for one minute. Shaft Radial Play: 0.06Max. Shaft Axial Play: 0.08Max. Remote is defined as islands and highlands; or a post code/zip code that is difficult to serve; or a suburb/town that is distant, inaccessible or infrequently served.

1 x USB CNC breakout board. 4 x TB6560 3.5A stepper motor driver. 4 x Stepper Motor 57BYGH56-401A. 1 x 250W 24V 10A power supply. The item "4 Axis 1.2N Stepper Motor 3.5A Driver TB6560 Nema23 USB Interface Board CNC Kit" is in sale since Thursday, December 26, 2013. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Other Automation Equipment". The seller is "prettyworthshop" and is located in Shenzhen. This item can be shipped worldwide.

Brand: HY
MPN: PR099SS
EAN: 0701233986368
Country/Region of Manufacture: China
Stepper Motor Driver: TB6560 3.5A
Stepper Motor: 57BYGH56-401A
Power Supply: 250W 24V 10A