3Axis CNC Kit Nema34 Stepper Motor 12Nm L150mm Motor Driver+Supply+5Axis Board

CNC Spindle Motor & Tool Parts. CNC 3Axis Kit Nema34 Stepper Motor 12Nm L150mm Motor Driver+Supply+5Axis Board.

BYG86 Stepper Motor 3Axis CNC Kit Nema34 12N. M L150mm Motor Driver&Supply&5Axis Board & Cable for Router Engraving Machine. 3 x Nema34 Stepper Motor L150mm.

3 x Stepper Motor Driver. Switching Power Supply 400W 60V 6.7A. 1 x 5 Axis CNC Breakout Board Interface. 1 x DB25 Parallel Cable. 1 x USB Power Cable.

Shaft Type: double-sided milling flat 1mm. Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal; 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode(pulse/pulse) , this input represents clockwise (CW) pulse. Active at high level or low level (set by inside jumper J1 & J2).

For reliable response, pulse width should be longer than 1.5µs. Series connect resistors for current-limiting when+12V or +24V used.

The same as DIR and ENA signals. DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside jumper J1 & J2), this signal is counter-clock (CCW) puls. For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW.

Please note that motion direction is also related tomotor-driver wiring match. Two wires for a coilto the driver will reverse motion direction. Enable signal: This signal is used for enabling/disabling the driver. High levelNPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling. For enabling the driver and low level fordisabling the driver.

Power supply, 1880 VDC or 24110VDC, Including voltage fluctuation and EMF voltage. Input voltage: AC110-230V (supports 110V has a pull switch). Output voltage: DC60V 6.7A.

5 axis CNC Breakout Board. Maximum support 5-axis stepper motor driver controllers. Compatible with MACH3, Linux CNC (EMC2) etc. USB power supply and peripherals powered phase are separated to protect computer security. All the signals are opto-isolated which can protect your computer security.

5-input interface to define the Limit, Emergence-Stop, Cutter alignment etc. Wide input voltage range: 12-24V, and with anti-reverse function. One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc. Output 0-10V analog voltage for inverter to control the spindle speed. USB port from PC or 12-24V power supply(optional).

Pulse and Direction Signal Control. Feedback is very important to us.

We can address your concerns. It is impossible to address issues if we do not know about them! Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount.

Mitsubishi, Siemens, Fagor CNC machine parts and accessories, Engraving & milling solutions, spindle. Motor with VFD kits, servo motor and servo drive kits, stepper motor and stepper drive kits, ball screw.

Linear guide rail, 3D printer parts, etc. If you need any CNC parts or repairs, welcome to contact me, we will try our best to help you. If it's non-workdays, please kindly be patient and wait till Monday. The item "3Axis CNC Kit Nema34 Stepper Motor 12Nm L150mm Motor Driver+Supply+5Axis Board" is in sale since Monday, August 3, 2020.

This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Electric Motors\Stepper Motors". The seller is "vipwindows_139" and is located in Shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

Brand: Sumtor
Model: 3-MA860H-86HS15060A4
Country/Region of Manufacture: China
Stepper motor drive: 2ph 24~110VDC AC18-80V 2~7.8A
Stepper motor: Nema 34
Holding Torque: 12N.in)
Rated Current: 6A
Power supply: 400W 60V 6.7A
Application: CNC Router Lathe
MPN: Does not apply
UPC: Does not apply
EAN: Does not apply