Cnc Axis Kit

3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU

3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU

3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU
3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A. For CNC Router Machine/3D printer. A ustria, B elgium, B ulgaria, C zechRepublic, D enmark, E stonia, F inland, F rance, G ermany, G reece. H ungary, I reland, I taly, L atvia, L iechtenstein, L ithuania, L uxembourg, M onaco, N etherlands, P oland.

P ortugal, R omania, S lovakia, S lovenia, S pain, S weden. 3× TB6600 stepper motor driver. 1× 4 Axis Mach3 USB CNC control board STB4100 V2.1. 1× 350W 24V DC Switching power supply.

100% Brand New and High Quality!! Nema23 Stepper motor 76mm/270Oz-in/ 3A 1.8Nm.

Step angle accuracy: ±5%(full step, not load). Temperature rise: 80deg Max(rated current, 2 phase on). Insulation resistance:100MO Min, 500VDC.

Insultion Strength--------500VAC for one minute. TB6600 stepper motor driver 4.5A. The working voltage is DC 10V-45V.

It is recommended to use switching power supply DC32V for power supply. Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.

Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560. The rated maximum output reaches: ±4.5A. Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A.

Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions. The working voltage is DC 10-45V; it is recommended to use DV32V switching power supply.

There are two input terminals, both of which adopt the common anode input mode. The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required. The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked. The motor rotates forward when CW is high or suspended, and reverses when it is low.

When EN is high or floating, it is working state, when it is low, it is offline. The power supply cannot be connected reversely, otherwise the chip will be burnt out. The set current should not exceed the rated current of the motor. Mach3 USB motion control board 4 axis.

The motion control card for machine control, with strong professional. Requires the operator to have the relevant expertise! Please strictly follow the instructions and warnings before using this product. If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power. It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.

Support for 4-axis linkage, you can connect four stepper motor drives or servo drives. Maximum step-pulse frequency is 100KHz, which is suitable for the servo or stepping motor.

4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stop. Switch, auto tool zero, home switch etc. Support for connecting electronic handwheel. Have 0-10V signal output, you can use mach3 software to control the spindle motor speed. 4 general-purpose isolated relay drive output interface, can drive four relays for controlling.

The spindle starts, forward rotating and reverse rotating, pumps or other device. 1 status LED, indicate connection status on the board. 350W 24V DC switching power supply. DC output: 24V 0-14.5A. DC voltage of Adjustable range: ±10%.

AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switch. Overload protection: 105%-135% cut off the output, automatic recovery.

Over-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recover. Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute.

Please note that due to the EU VAT reform policy implemented on 1 July 2021. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Other Automation Equipment". The seller is "powace08" and is located in this country: DE. This item can be shipped to all countries in Europe.
  • Modified Item: No
  • Country/Region of Manufacture: China
  • Custom Bundle: No
  • Step Angle(degrees): 1.8deg
  • Driver name: TB6600
  • Stepper motor size: 57x57x76mm
  • Current: 3A
  • Phase: 2
  • Lead Wire: 4pcs
  • Type: 4 axis stepper motor usb controller kit
  • Power supply: 350W 24V
  • Non-Domestic Product: No
  • Motor: 23HS8430/TB6600
  • Breakout board: 4 Axis Mach3 USB Motion Card
  • Driver Voltage: DC 10V-45V
  • Brand: RATTM MOTOR

3 Axis Nema23 USB Mach3 CNC Kit Stepper Motor TB6600 Driver 270oz-in 76mm 3A? EU