3 pcs Stepper motor driver DM542A, PEAK 4.2A, 128 micsteps. 1 pc Power supply 350W-36vdc/9.7A. 1 pc parallel cable & 1 pc breakout board.
High torque, More smooth movement. High efficiency, energy-saving, low noise, low vibration, high start torque, low start current and reliable performance. We offfer mach 3 software by free, if you want please download on our website. Step Angle: 1.8 degree.Number of wire leads: 4. RED A+ , GRN A-, RED B+, BLU B. The front shaft diameter is 8mm, the rear shaft diameter is 6.35mm. Overvoltage, under voltage, overcorrect, phase short circuit protection. Pulse signal, PUL+ is the positive end of pulses input pin. PUL- is the negative end of pulse input pin. DIR signal: DIR+ is the positive end of direction input pin. DIR- is the negative end of direction input pin. Enable signal: ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver. ENBL- is the negative end of direction input pin. PCs control signals can be active in high and low electrical level.
When the high electrical level. Is active, all control negative signals will be connected together to GND.
Is active, all control positive signals will be connected together to public port. Examples(Open collector &PNP), please check them. Input port circuit (Yang connection). 2 Input port circuit (Yin connection). R must connect in the control signal part.Function choice (Using DIP pins to achieve this function). 1 Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table. SW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the selected dynamic current and ON meaning that standstill is set to be the same as the selected dynamic current. The first three bits (SW 1, 2, 3) of the DIP switch are used to set the dynamic current. Closest to your motors required current. Semi-flow function is that there is not step pulse after 500 ms, the driver output current automatically reduced to 70% of rated output current, which is used to prevent motor heat. +V: Power supply, 1650 VDC, Including voltage fluctuation and EMF voltage. The max current is 5A. (2) A+ A- B+ B-Connecting 2 phase stepper motors. The driver & 2-phase hybrid stepping motor use four-wire connection, the motor can be connected in parallel & series bipolar. As for bipolar connection, it is higher performance with high-speed, but the current of driver is larger (it is 1.73 times more than the motors winding current). Connecting in series, the drivers current is equal to the motor winding one. There should be 20mm of space, it cant be placed next to other heating devices, to avoid dust, oil mist, corrosive gas, humidity and strong vibration places. 1, the status on lights indication. RUN: green, normal work light. ERR: red, failure light, the motor with phase short-circuit, overvoltage and under-voltage protection. Motor doesnt run, without holding torque. Wrong connection of stepper motor. RESET signal is effective when offline. Adjust PMW & signal level. Change connection for any of 2 wires. Motors holding torque is too small.
Too small relative to current setting. Driver does not match with the motor.A complete stepper motor control system should contain stepper drives, DC power supply and controller (pulse source). The power is 350Watts, and the output voltage is 36VDC. Description: Built in DB25 male connector.
DB25 Output Pin:P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. DB25 Input Pin: P10, P11, P12, P13, P15. High quality with Surface-mount Tech. P2 P3 is set to X-axis for the X-axis pulse. P4 P5 is set to Y-axis, Y axis pulse.
P6 P7 is set to Z-axis Z-axis pulse. The other can be set to A B C axis.A-axis pulse P8 P9 is set as the A axis. P14 is set to B-axis B-axis pulse P1. P16 P17 is set to C-axis, C axis pulse. Can also be set to the spindle control signal \ electrical permit. Input interface for the P10 P11 P12 P13 P15.
Our Stepper Motors are used on small to mid-sized CNC mills or milling machines, CNC lathes, Pick-n-place machines. Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters. Automazation, 3D Printer, Stage lighting, instrument, laser equipment, scanner and so on. These motors have been used in precision. Telescope positioning systems and robots.
The item "3 axis Nema23 stepper motor 425oz-in Dual & Drivers DM542A CNC kit" is in sale since Tuesday, February 28, 2017. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Electric Motors\Stepper Motors". The seller is "longsmotor99" and is located in Denmark. This item can be shipped worldwide.