Cnc Axis Kit

FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm

FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm
FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm

FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm

FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm for CNC Router Engraving Milling Machine. 4 x 23HS2430B Nema23 stepper motor (Dual Shaft) 112mm, 425oz, 2.8N. 4 x CW5045 stepper motor driver 24- 50V, 4.5A, 256microstep. 1 x 400W 36V/11A switching power supply.

1 x 5 Axis mach3 breakout board V5 type. 1 x DB25 parallel cable. 4 Axis for medium size Router Mill Plasma or Laser.

It can most connection 5pcs driver and control 5pcs motor in the same time. It is with 4-wire limit switch to insure our safty movement. It is with relay port to contro the cnc spindle.

Working voltage is 5VDC and support with MACH3, EMC2, KCAM4 software. 25-pin parallel port control is defined as follows. The pin of the drive board. B(Fifth axis)pulse signal. X(First axis) pulse signal. X(First axis) direction of the signal. Y(Second axis)direction of the signal. Z(Third axis) pulse signal. Z(Third axis) direction of the signal. A(Fourth axis) pulse signal. A(Fourth axis) direction of the signal. B(Fifth axis) direction of the signal. CW5045 high microstep stepper motor driver.

Output current: 1.3,1.8,2.3,2.7,3.2,3.7,4.2,4.5A. Mircostepping: 1(1.8┬░), 1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256. 1/5,1/10,1/25,1/50,1/125,1/250. Protect form: Overheated protect, lock automatic half current , error connect protect.

It is fit for NEMA17-23 two and four phase stepper motors whose current is small than 4.5A. Full current or half current choice : SW4:0=Full current; 1=half current. To avoid use in the oil contamination, dust and corrosive gas environment. To lay it in a place with good ventilation. Pls note the connection with right power(+ and -) to avoid broken the driver. Pls test it when confirm the connection is right. Step angle accuracy:+ - 5%(full step, not load). Resistance accuracy: + - 10%. Inductance accuracy:+ - 20%. Temperature rise: 80deg Max(rated current, 2 phase on). Ambient temperature ----------20deg ---- +50deg.

Insulation resistance:100ohm Min, 500VDC. Insultion Strength--------500VAC for one minute. 400W, Input:100-120VAC or 200-240VAC, 50/60Hz, Output:36v/9.7 A, single output switching power supply. Please give us the opportunityto resolve any problem when you have, we concern your problem and we will try our best to resolve it.

Item must be in it's original condition and no physical damage. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos. The item "FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm" is in sale since Thursday, March 25, 2021. This item is in the category "Equipamiento y maquinaria\Automatiza., motores y ejes\Motores el├ęctricos\Motores paso a paso". The seller is "kuku218" and is located in Frankfurt. This item can be shipped to European Union member countries.

  • Marca: RATTM MOTOR
  • MPN: No aplicable
  • Phase: 2 phase
  • Current: 4.5A
  • Shaft: 57x57x112mm Dual Shaft
  • Type: Hybrid
  • Shaft Diameter: 8mm Diameter
  • Breakout board: 5 Axis breakout board V5 type
  • Driver: CW5045 4.5A,256 microstep
  • Software: MACH3,EMC2,KCAM4 etc
  • Lead wire: 4pcs
  • Power supply: 400W,36V/9.7A
  • Driver Voltage: 24-50V DC
  • Port: LPT
  • Application: CNC Routers/Milling Machine, Engraver Machine
  • Step Angle(degrees): 1.8 degrees
  • Holding torque: 425oz-in 2.8N.


    FRA4 Axis LPT MACH3 CNC Controller Nema23 Stepper Motor Driver Kit 425oz 112mm